Selasa, 25 Januari 2011

TVs SHARP series silver box

Tips and tricks this time talking about how where to face problems on Sharp TVs series silver box is easy and practical. First you clean them with thinner mainboard if so dirty solderan point in seluru circuit can diligat clearly. Once clean solderao try to check all the points in all sections, especially in the supply-Flyback Vertikal-Regulator/Power, because the damage is often the case in point because the heat solderan in timbulkan.coba also check solderan vertical IC and resistors, if there is no problem with solderanya try to check the IC Vertical and resistonya whether damaged or not, if you believe it damaged sila replace with the same number as well as sesistornya.
Try to turn on the TV and see if masi star normally would not please take the following rare;


First;
if the flame red LED to yellow-green and stop damage to the memory IC (24c0424c16) replace it with a new setting in the service menu again prameter.

Second;
If the red LED continues to die of damage occurred on the main IC TDA 938psxxx. Or loss of voltage on the 3.3 volt regulator, check the pawer supply.

Third;
If the green or red blink there is an error in the memory IC (internal error) you can reset it or replace it IC. How to reset the memory IC SHARP will be displayed on the theory kehusus.

Fourth;
If the green for 5-10 seconds and the red back is a failure on the horizontal section, check the FBT (flyback) try and measure the wear multitester with 10k scale Ground on foot and leg toward the collector transistos Horizontal out put, If it moves even a little mean FBT ( flyback) is short also check the voltage 180v to RGB blog. Biaasa also limiting damage to the resistor.


fifth;
If the led is not lit at all check the power supply input section 6553/6554 replace STR check if there were signs of damage and do not forget to also check the limiting resistor (6.8 / 10 watt). In the process of replacement IC STR 6553/6554 check all diodes especially 2 buag diodes in the corner if necessary, replace it with a genuine reason not to an imitation of imitation heart STR certainly will die back, and this often happens if they do not get the same type diodes what if IN 4667 two diodes that exist in TVs SHARP series silver box in the connection in series meggantikan dae in pairs to each one such diode.
Read more...

________________________________________

Picture|Thosiba

TOSHIBA-2545DE (TA8808)
• Regulators and relays are not stable (PUM-up): Check out the Horizontal oscillator, and replace the crystal with the 500F2 503F30 usual

THOSIBA-20N3XE (Bomba)
• The color is lost, the normal picture: Replace IC TB1231

THOSIBA-1450XNE (dramatic Vision)
• Regulators are unstable: Check D873 (16V zener) on regulator

THOSIBA-2955DE
• Auto Search is good, no color pictures, sounds gorok: Check Adjust L671 in SIF module

TOSHIBA-2840XH
• Vertical defect resistor, capacitor elco, IC, nice all: Check out Vertical driver feedback voltage is normally 3-4 volt
Read more...

________________________________________

Samsung-Cb

SAMSUNG-CB3339Z
• Blanking: check the voltage 5v (7805)

SAMSUNG-BIO-CB3366Z
• Blanking (normal Vcc): replace the chroma IC M52309SP

SAMSUNG-CB2039Z
• Tuning no channel (33v, VT Normal): 12v voltage check
SAMSUNG-CB3862X
• Pictures open ditenga about 5cm, IC Vertical nice: G anti elco vertically out 1000uf/35v
SAMSUNG-CB3366Z
• SMR 40 000 Damaged, damaged again after the change: replace the first driver module HIS 6169
Read more...

________________________________________

Check and replace

Goldstar-Soudmax
Color is sometimes missing: check and replace cramic pin 11 of IC TDA8690

Goldstar-C14D22
No sound, standard tuning does not stop: check Q06 (C3198)

Goldstar-C14D22
Standby, in turn it can not, led is flashing: check 6v8 zener diodes in the PSU, if distar led is dead: check SE 110

Goldstar-CA14A95C
Standard tuning does not stop: replace Ucom GS8334-02B

Goldstar-CA14A62
Image thinning replaced PIF Stay the same: check Z201 (CF5, 5MHz)

Goldstar-CF14D20
Fig sometimes colored sometimes not: open the base legs Q07 R73

Goldstar-CF14D20
In the star led the flame, continue to die (no standby): check pin 9 S6707, if not stable (PUM up) check FR813 (1ohm) and ZD803 (9V1)

Goldstar-CBS4821
There is no color, when there are new hot Delay IC color: replace the MC144111. To test it go to pin 4 and hold color.

Panel presets do not work: go to pin 6

Goldstar-CF14A170D
No sound IC LA7555 Good Audio): check L201 (SIF 6.0 MHz) and the damaged capacitor (82pf)

Goldstar-Soudmax
Blanking, RGB VCC nice: replace TA8690

Goldstar-Soudmax
Standby with the position of blinking LED lights: replace diode RU2k near STR 6707 with D IN4007 also replace: C330 (470uf/35v)

Goldstar / LG
Often turns itself to standby, if the remote at the switch on the TV to life again, but went back to standby after a few hours: replace Elco Driver Horizontal (10uf/100v)
Read more...

________________________________________

repair and easy

PANASONIC-TC20T8
Regulators did not work (dead): check Q8 1 (C5253/C4804) and Q805 (A1512/A733)

PANASONIC (AN5601)
There is no color, in Fine tuning is: check Trans amplifier delay (C1685) not delay line


PANASONIC-TC1613R
As if tuning slide (slip) and not syncron, good sound: check R125 (3k3) 1k2 replace with

PANASONIC-TC2088DX
The contrast is not working, sometimes appears a vertical line, a nice picture: check the ABL resistor (37K)

PANASONIC-TC1450
Blanking and protectionism: replace the AN 5600

No sound: check the Q1112, Q1113 (N4212) and change C114

PANASONIC-TC2088
Bright, contras, the color of the OSD function is not normal: Check the ABL resistor (63k)
Read more...

________________________________________

Senin, 24 Januari 2011

quick and easy

POLITRON-GM1483
• OSD does not exist: please go to the R723 and D732

POLITRON-P in P
• Tuning geses and blanking, OSD nice: check tuner (digital 5v) damaged one of them

POLITRON (Regulator TDA8380)
• B + is not stable (PUM-up): increase in the priner Filter 15V regulator so 2200uf

POLITRON-GM1492
• Tuner Menual not stop: Replace Transformer AFT with E08L

POLITRON (AN5435 = TDA3565)
• Vertical can not be silent, V.hight not optimal: instead of AN5435 and R127 (13k)


POLITRON-BB1740
• As if tuning slide, VIF is good BI continues: check Transistor Band switch T708(BC548)

POLITRON-PN20123K
• PROTEK, distar live and die (Vcc good): replace IC 4558 near the amplifier Vertical

POLITRON-GM1490
• Phase Horizontal shear (no black line) is almost to center: check R449 (68) to pin12

POLITRON-LFS1465
• Led channel flame all, the presets are not support: check R18 (10k) on pin 19(UPC 1363)

POLITRON-PN14123KAG
• Can not star, there is no horizontal oscillator, VCC nice: replace TDA 8841

POLITRON-Lawas
• thick black lines up and down both the position of the AV and in the Channel:replace Plyback (FBT)
Read more...

________________________________________